Georgia Master Plumber Class II Non-Restricted License

The Master Plumber Class II Non-Restricted License allows you to do the following work:

Plumbing services for:
- All types of dwellings
- All types of structures

How to Get the Master Plumber Class II Non-Restricted License in Georgia?

Meet the work experience requirement which is with industrial or commercial plumbing
Present the documents listed below to the Georgia State Division of Master and Journeyman Plumbers:
- Background Check (it can be obtained at the local law enforcement office)
- Three notarized references from people who know the candidate’s plumber experience to whom the Division may refer. Applicants must submit the Reference Form found within the application
- Disciplinary Action/Sanctions (if applicable)
- Applicant Affidavit of Citizenship
- Qualified alien documentation
- Secure and Verifiable Documents
- Immigration Documents (If applicable)
- Copy of a current and unexpired photo ID card showing brazing and installation expiration dates (If holding a Medical Gas Certification)
Await for the Division’s response to register for the examination. The Division will get in touch with AMP/PSI© to inform them of the approval
Take and pass the corresponding exam
Expect the Division to issue the license after approved

Georgia Master Plumber Class II Non-Restricted License Exam Prep Course

indicador

Georgia Master Plumber Class II Non-Restricted License Exam

Below is all the information related to the trade exam, including the official reference list.

Georgia Master Plumber Class II Non-Restricted Trade Exam

Testing Method: Computer-based testing; closed book
Testing Company: PSI©
Number of Questions: 168
Types of Questions: Multiple choice
Time Allowed: 7 Hours
Minimum Passing Score: 98 Questions (70%)
Subjects Involved (No. of Questions):
- Pretest questions (28) *Pretest questions do not affect the score
- Restricted/Unrestricted (100)
  - Comply with General Laws (5)
    
    Georgia Construction Industry Licensing Board (complaint procedures, function of, renewal, etc.)
    
    Location law for underground utilities
    
    Americans with Disabilities Act (ADA)
    
    American National Standards Institute (ANSI) Handicap Accessibility
    
    State Water Conservation Law
  - Comply with Regulations (15)
    
    Georgia State Plumbing Code and Standard Building Code Congress (SBCCI) Plumbing Code
    
    Standard Building Code Congress (SBCCI) Gas Code
    
    Code of Federal Regulations, Title 29, Part 1926 (OSHA)
    
    Obtain necessary permits and inspections (plumbing, boiler, etc.)
    
    State Trenching Law
    
    Georgia State Boiler Code
    
    Health Department
    
    Manufacturer's recommendations
  - Work Planning/Organizing (7)
    
    Compile bill of materials from drawing and specifications (job takeoff)
    
    Interpret equipment name plate data: pump, water heater, backflow preventer, lift stations
    
    Draw waste and water diagrams (isometrics)
    
    Interpret bar chart schedule
    
    Determine precedence of various codes, laws, manufacturer's instructions, regulations, etc.
  - Perform Pipe Cutting and Joining Activities (10)
    
    Cut cast-iron pipe (using snap-type chain cutter, hammer and chisel, metal saw, demolition saw, hydraulic cutters, etc.)
    
    Cut concrete pipe (using saws, hammer and chisel, etc.)
    
    Cut and ream copper tubing and pipe (using metal saws, tubing cutter, etc.)
    
    Cut and ream plastic pipe (using saws, tubing (scissor) cutter, etc.)
    
    Cut and ream steel pipe (using hand pipe cutter, metal saw, power pipe cutter)
    
    Join cast-iron soil pipe (using lead and oakum, rubber-type seal, no-hub)
    
    Use transition fittings (clay pipe to cast-iron pipe, cast iron to plastic, etc.)
    
    Join copper or brass pipe (tubing) to fittings (sweat method, compression, flare, T-drill method, etc.)
    
    Join PVC, CPVC plastic pipe using solvent method, fusion method, threaded, grooved, etc.
    
    Cut and join ductile iron pipe
    
    Join steel pipe (threaded, welded, grooved, flanged, etc.)
    
    Cut and join vent and flue pipe (Class B and C)
    
    Cut and join other types of pipe (glass, polyethylene, acid resistant, etc.)
  - Perform Plumbing Systems Installation Activities (21)
    
    Interpret plans and install according to specifications
    
    Size and install water supply
    
    Size and install drainage systems
    
    Size and install gas pipes
    
    Assemble plumbing fittings and fixtures (interpret manufacturer's instructions)
    
    Locate/mark holes for plumbing in walls, ceilings, or floors
    
    Install pipe through concrete walls, ceilings, or floors
    
    Install pipe through wood floors
    
    Install pipe through metal walls, ceilings, or floors
    
    Install pipe to meet fire code regulations
    
    Secure horizontal and vertical lines of pipe to masonry and concrete, metal, etc., surfaces
    
    Secure horizontal and vertical lines of pipe to wood surface
    
    Insulate water lines
    
    Locate and install clean-cuts
    
    Install pipe in trenches (layout, digging, compaction, bedding, and thrust blocks)
    
    Install footing drains
    
    Calculate the slope required for building sewer lines
    
    Install vent terminals (roof-flashing)
    
    Fabricate fixture support (backing)
    
    Mount fixture carriers
    
    Install bathroom fixtures: water closet, tubs, showers, bidets, lavatories, etc.
    
    Install clothes dryer vent
    
    Install/fabricate sump reservoir
    
    Install sinks
    
    Install dishwashers
    
    Install garbage disposal
    
    Install “Instant Hot” water heaters
    
    Install water heaters
    
    Install boilers
    
    Install specialty fixtures: hospital, medical, restaurant, prison, etc.
    
    Install industrial piping and fixtures
    
    Install specialty piping: gas, air, vacuum, etc.
    
    Install valves according to manufacturer's instructions
    
    Install specialty valves: backflow, T and P, pressure relief, check, vacuum relief, backwater, pressure-reducing, etc.
    
    Install specialty traps and interceptors (grease, sand, oil, etc.)
    
    Install shower and safety pans
    
    Install fixtures according to ADA, ANSI regulations
    
    Install specialty waste systems (continuous, indirect, and safe waste systems, open site drains, trailer site waste systems, etc.)
    
    Install roof and storm drain systems
    
    Install sewage ejection systems
  - Perform System Testing Activities (7)
    
    Pressure test water distribution system (air, water, hydrostatic, etc.)
    
    Test sanitary and drainage systems (water, smoke, air, peppermint, etc.)
    
    Pressure test gas lines (air)
    
    Certify backflow test
    
    Sterilize potable water systems and obtain certification
  - Perform Maintenance and Repair Activities (15)
    
    Locate leaks in gas supply lines (using soapy water, gas detector)
    
    Service gas appliances (clean and adjust gas burners, check valves and venting, etc.)
    
    Service electric appliances (replace electric water heater element, check controls, relief valves, etc.)
    
    Locate, identify, and remove obstructions in drain lines and water closets
    
    Clean backwater valves
    
    Repair leaking water faucets or valves
    
    Repair tank type and flush valve water closets
    
    Locate leak in drainage/vent systems (peppermint test, Smoke test)
    
    Free jammed garbage disposal
    
    Test/adjust pressure reducing valves
    
    Test/replace thermocouple and/or pilot light
    
    Service backflow preventer
    
    Service sewage pumps
    
    Locate underground lines
  - Safety-related Issues (15)
    
    Identify and control for the following potential safety hazards during installation and service:
    
    Hot water heater and pressure vessels (vent system – slope, classification, sizing, routing and termination; testing, relief valves – sizing, pressure rating, routing and termination, etc.)
    
    Gas piping: testing and support
    
    Backflow prevention
    
    Personal safety: poisonous gases, trenching, faulty equipment, etc.
  - Calculate the following during installation and service: offset, volume, area, pressure, depth, circumference, radius, weight, etc. (5)
- Administrative/Business/Design (40)
  - Comply with Business Laws (15)
    
    Workers' compensation
    
    Unemployment insurance
    
    Employer's tax guide (circular E)
    
    State sales and use tax
    
    Business license
    
    Completion of I-9 form
    
    Lien Rights
  - Administrative Requirements (15)
    
    Bonding and liquidated damages
    
    Insurance: liability, property damage, auto, etc.
    
    Financing and cash flow
    
    Bookkeeping and accounting
    
    Job cost estimating and bidding procedures
    
    Contracts and purchase orders
    
    Scheduling and project management
    
    Accident or incident reports
  - Plumbing System Design (10)
    
    Select sump reservoir
    
    Select water heaters (size and capacity)
    
    Select boilers (size and capacity)
    
    Select specialty fixtures: hospital, medical, restaurant, prison, etc.
    
    Select industrial piping and fixtures
    
    Select specialty piping: medical, gas, air, vacuum, etc
    
    Select sewage ejection systems
    
    Select valves: backflow, T and P, pressure relief, check, vacuum relief, backwater, pressure-reducing, according to manufacturer's specifications
    
    Select specialty traps and interceptors (grease, sand, oil, etc.)
    
    Select shower and safety pans
    
    Select fixtures according to ADA, ANSI regulations
    
    Select specialty waste systems (continuous, indirect, and safe waste systems, open site drains, trailer site waste systems, etc.)
    
    Select roof and storm drain systems
PSI© Master Plumber Class II Non-Restricted Official Content Outline

Georgia Master Plumber Class II Non-Restricted Book Set

This set of books includes all required references for the Master Plumber Class II Non-Restricted exam. Orders placed before 2 PM are shipped the same day via UPS and a tracking number is emailed before 3 PM.

GEORGIA MASTER PLUMBER CLASS II NON-RESTRICTED - BOOK SET WITHOUT TABS INCLUDES ALL BOOKS FOR TRADE AND BUSINESS EXAMS

Sales price: $1,161.15
GEORGIA MASTER PLUMBER CLASS II NON-RESTRICTED - BOOK SET WITH TABS INCLUDES ALL BOOKS FOR TRADE AND BUSINESS EXAMS

Sales price: $1,261.15